PLA+ Pine Green Filament 1.75mm 1Kg eSun

PLA+ from eSun is an enhanced PLA filament and one of eSun's most popular materials. According to eSun it is considerably stronger and tougher than standard PLA and less likely to break, yet just as easy to print. Parts come out with smooth surfaces and clean layer lines and stand up well to everyday use. Whether prototype, bracket, enclosure or figure: PLA+ is a safe choice for almost any project and also runs reliably on fast printers. The spool holds 1 kg of 1.75 mm filament in the colour Pine Green. It comes on a cardboard spool that goes into cardboard recycling when empty instead of the bin.

More colours PLA+:
                                                                                                   

Recommended Accessories:

• Filament dryers (dry box): all models in our shop
• Filament Vacuum Set Pro 3 eVacuum by eSun
• 5 Pcs. Filament Vacuum Bags Pro 3 from eSun
• 1 Liter Isopropyl Alcohol/Isopropanol 99.8%
• 3DLac Adhesive Spray 400ml

Features:

• Tough and hard to break, according to eSun considerably stronger than standard PLA
• Easy to print, smooth surface and clean layer lines
• Also runs very well on fast printers: up to 300 mm/s, a speed rarely used in practice
• Holds up outdoors, but may fade over time in strong sunlight. Softens from about 53 °C
• If a part has to withstand heat, for example in a car: HT-PLA from Polymaker or R3D
• Cardboard spool instead of a single-use plastic spool: less waste, the empty spool goes into cardboard recycling
• Coated edges on the cardboard spool: less abrasion, runs well in the Bambu Lab AMS and the Creality CFS
• Vacuum-packed with desiccant

Application Examples:

• Prototypes and functional samples
• Mechanical parts such as brackets, housings and covers
• Cosplay parts and props
• Models, figures and decoration

Documentation:

• PLA+ technical data sheet (PDF)
• PLA+ safety data sheet (PDF)

Recommended Print Settings:

• Nozzle temperature: 220 °C (210 to 230 °C)
• Print bed temperature: 55 °C (45 to 60 °C)
• Print bed: PEI (textured)
• Part cooling fan: 100 %
• Print speed: slicer's default profile, up to 300 mm/s

Technical Data:

• Manufacturer: eSun
• Material: PLA+ (enhanced PLA)
• Colour: Pine Green
• Filament diameter: 1.75 mm
• Tolerance: ±0.05 mm
• Filament weight: 1 kg
• Density: 1.24 g/cm³
• Melt flow index: 3.7 g/10 min (190 °C / 2.16 kg)
• Heat deflection temperature: 53.78 °C (0.45 MPa)
• Tensile strength: 70.37 MPa (X-Y), 36.36 MPa (Z)
• Elongation at break: 4.14 % (X-Y), 2.92 % (Z)
• Flexural strength: 100.3 MPa (X-Y), 56.4 MPa (Z)
• Flexural modulus: 3259.39 MPa (X-Y), 2873.94 MPa (Z)
• Izod impact strength: 7.27 kJ/m² (X-Y), 2.22 kJ/m² (Z)
• Spool: cardboard
• Spool outer diameter: 200 mm
• Spool hole diameter: 55 mm
• Spool width: 62 mm
• Gross weight: 1303 g

Scope of Delivery:

• 1× PLA+ filament Pine Green, 1.75 mm, 1 kg on cardboard spool