2x18650 Lithium Battery Shield Dfrobot 5V 2A / 3.3V

The battery holder from DFRobot takes two 18650 cells and turns them into a 5 V and 3.3 V supply. Charging is done via Micro-USB or USB-C, output via a USB-A socket and five connections each for 5 V and 3.3 V. A protection circuit prevents overcharging and deep discharge, four LEDs show the charge level. Batteries are not included.

Caution: Pay attention to + and – when inserting the cells. According to DFRobot the new version has reverse polarity protection and an acrylic base plate, on a board without reverse polarity protection a wrongly inserted cell destroys the charging chip.


Features:

  • For two 18650 cells
  • Charging via Micro-USB or USB-C
  • Outputs: 1 × USB-A with 5 V, 5 × 5 V, 5 × 3.3 V
  • Protection against overcharging and deep discharge, reverse polarity protection on the new version
  • Button: short press switches on, pressing twice within 1 s switches off
  • DIP switch HOLD or NORMAL: NORMAL switches off at low current, HOLD keeps the output on until the deep discharge protection trips
  • LED1 to LED4 show the charge level, they blink while charging and light steadily when the cells are full
  • According to DFRobot use cells of the same brand with similar voltage

Application Examples:

  • Mobile power for ESP32, Arduino and sensors
  • Vehicles and robots
  • Outdoor devices

Documentation:


Technical Data:

  • Manufacturer: DFRobot
  • Manufacturer SKU: DFR0969
  • 5 V output: 2 A, at most 3 A (not recommended, depends on the cells)
  • 3.3 V output: 1 A
  • Output connections: 1 × USB-A (5 V), 5 × 5 V, 5 × 3.3 V
  • Input: Micro-USB and USB-C, 5 V
  • Protection: overcharging, deep discharge, reverse polarity (new version)
  • Dimensions: 103.5 × 48 × 20 mm
  • Weight: 30 g

Scope of Delivery:

  • 1× 2x18650 Lithium Battery Shield Dfrobot 5V 2A / 3.3V
  • Batteries are not included

Write a review

Note: HTML is not translated!
    Bad           Good

2x18650 Lithium Battery Shield Dfrobot 5V 2A / 3.3V

  • Brand: DFRobot
  • Product Code: 422355
  • Availability: In Stock
  • CHF12.90

  • Ex Tax: CHF11.93

Related Products

2x18650 Lithium Battery Shield 5V 3A / 3V 1A

2x18650 Lithium Battery Shield 5V 3A / 3V 1A

This battery shield holds two 18650 cells and uses it to supply a Raspberry Pi, Arduino, ESP8266 or ..

CHF8.90 Ex Tax: CHF8.23

1x18650 Lithium Battery Shield 5V 3A / 3V 1A

1x18650 Lithium Battery Shield 5V 3A / 3V 1A

This battery shield holds one 18650 cell and uses it to supply a Raspberry Pi, Arduino, ESP8266 or E..

CHF9.90 Ex Tax: CHF9.16

4x18650 Lithium Battery Shield 5V 3A / 3V 1A

4x18650 Lithium Battery Shield 5V 3A / 3V 1A

This battery shield holds four 18650 cells and uses it to supply a Raspberry Pi, Arduino, ESP8266 or..

CHF16.90 Ex Tax: CHF15.63

UPS HAT for Raspberry Pi Uninterruptible Power Supply

UPS HAT for Raspberry Pi Uninterruptible Power Supply

With this Waveshare UPS HAT, a Raspberry Pi keeps running from two 18650 cells during a power interr..

CHF23.90 Ex Tax: CHF22.11

Solar Power Manager (C) for 6-24V Solar Panel

Solar Power Manager (C) for 6-24V Solar Panel

This is a Solar Power Manager from Waveshare. The Power Manager supports panels from 6-24V, thus cha..

CHF23.90 Ex Tax: CHF22.11

UPS UPS Module 5V 5A Uninterrupted 18650 Battery Board

UPS UPS Module 5V 5A Uninterrupted 18650 Battery Board

With the UPS Module 3S for your Raspberry Pi, you get a reliable uninterruptible power supply that s..

CHF25.90 Ex Tax: CHF23.96

Tags: 2-fold, battery shield, 18650, ESP32, ESP8266, Arduino, Li-Ion, cell, battery, battery operation, battery compartment, lithium, Li-Ion battery, lithium ion battery, charge controller, DFRobot, DFR0969, power bank