4x18650 Lithium Battery Shield 5V 3A / 3V 1A
This battery shield holds four 18650 cells and uses it to supply a Raspberry Pi, Arduino, ESP8266 or ESP32 with 5 V and 3 V. The built-in charging electronics recharge the cells via USB, the protection electronics protect against overcharging and deep discharge. Batteries are not included.
Caution: Observe the + and − polarity when inserting the 18650 cells, otherwise the charging chip will be destroyed. The holders are designed for 18650 cells without protection electronics, about 65 mm long. Longer cells with protection electronics do not fit. Only use cells of the same type with the same state of charge together.
Recommended Accessories:
Features:
- Protection against overcharging and deep discharge
- Charging via micro USB or USB-C with up to 0.5 A
- 5 V 3 A via USB type A or 5 solder pads 5 V
- 3 V 1 A via 5 solder pads 3 V
- 4 red LEDs show the state of charge
- After inserting the cells, briefly power the shield via USB, only then does it switch on
- A short press on the side button K1 shows the state of charge and switches on
- Switching off the 5 V and 3 V outputs: press button K1 for more than 3 seconds, on the new version press it briefly twice
Application Examples:
- Mobile power supply for Raspberry Pi, Arduino, ESP8266 and ESP32
- Power bank for USB devices in custom projects
Technical Data:
- Number of 18650 cells: 4
- Protection electronics: overcharge and deep discharge protection
- Charging: micro USB and USB-C
- Maximum output current 5 V: 3 A (tested briefly up to 4 A)
- Maximum output current 3 V: 1 A
- Outputs: 1× USB type A socket 5 V, 5× solder pads 5 V, 5× solder pads 3 V
- Mounting holes: 4× diameter 3 mm
- Dimensions: 102 × 96 × 22 mm
- Weight: 67 g
Scope of Delivery:
- 1× 4x18650 Lithium Battery Shield 5V 3A / 3V 1A
- Batteries are not included
4x18650 Lithium Battery Shield 5V 3A / 3V 1A
- Brand: purecrea
- Product Code: 421084
- Availability: In Stock
-
CHF16.90
- Ex Tax: CHF15.63
Related Products
Pin header male 1 X 40 pole RM 2.54mm straight short pin
This straight pin header with short pins is suitable for soldering onto boards and for breadboards. ..
CHF0.80 Ex Tax: CHF0.74
2x18650 Lithium Battery Shield 5V 3A / 3V 1A
This battery shield holds two 18650 cells and uses it to supply a Raspberry Pi, Arduino, ESP8266 or ..
CHF8.90 Ex Tax: CHF8.23
1x18650 Lithium Battery Shield 5V 3A / 3V 1A
This battery shield holds one 18650 cell and uses it to supply a Raspberry Pi, Arduino, ESP8266 or E..
CHF9.90 Ex Tax: CHF9.16
UPS HAT for Raspberry Pi Uninterruptible Power Supply
With this Waveshare UPS HAT, a Raspberry Pi keeps running from two 18650 cells during a power interr..
CHF23.90 Ex Tax: CHF22.11
Solar Power Manager (C) for 6-24V Solar Panel
This is a Solar Power Manager from Waveshare. The Power Manager supports panels from 6-24V, thus cha..
CHF23.90 Ex Tax: CHF22.11
2x18650 Lithium Battery Shield Dfrobot 5V 2A / 3.3V
The battery holder from DFRobot takes two 18650 cells and turns them into a 5 V and 3.3 V supply. Ch..
CHF12.90 Ex Tax: CHF11.93
UPS UPS Module 5V 5A Uninterrupted 18650 Battery Board
With the UPS Module 3S for your Raspberry Pi, you get a reliable uninterruptible power supply that s..
CHF25.90 Ex Tax: CHF23.96
UPS HAT 5A 4x18650 Battery Board for Raspberry Pi 5
This DFRobot UPS board is screwed under the Raspberry Pi 5 and supplies it via spring contacts (pogo..
CHF55.90 Ex Tax: CHF51.71
10W Solar Power Kit 12V / 5V Outputs monocrystalline panel
This DFRobot solar kit powers measuring stations and IoT devices outdoors without a mains connection..
CHF46.90 Ex Tax: CHF43.39
Tags: Batterieshield, 4x18650, Raspberry, ESP32, ESP8266, Arduino, LiPo, Li-Ion, NCR18650B, Panasonic, Cell, Battery, Battery operation, Battery operation, 18650, Battery compartment, Lithium, Lithium block, Li-Ion battery, Lithium Ion battery, Built-in battery, Special battery, Industrial battery, V8, V9, Charge controller, Raspberry.















