HALENG I²C Doctor I2C Bus Tester and Analyser White

The I²C Doctor from HALENG is a handy diagnostic tool for the I²C bus. It reveals faults at the electrical level within seconds and suggests concrete improvements. At its heart is an ESP32 (dual-core, 240 MHz, 4 MB flash), and the results appear on a 1.3-inch TFT with 240 × 240 pixels. Connection is via GROVE/STEMMA, QT/Qwiic or two 2.54 mm pin headers (male/female). The automatic diagnosis checks the whole bus, detects short circuits between SDA, SCL, GND and VDD, rates the pull-up resistors and calculates a quality score from 0 to 100 %. In addition there is an address scanner with a built-in sensor database, a pull-up analysis with live measurement of resistances, rise times and currents, and a passive live monitor for running communication. Fault injection simulates long cables, EMC noise, SDA hold and clock stretching, the stress test checks the stability of individual devices, and the sensor simulator emulates I²C slaves for firmware development. With the USB/I²C bridge the bus can be controlled directly from a PC; HALENG provides a Python script for this. Switchable pull-ups (10 kΩ, 4.7 kΩ, 2.2 kΩ, 1 kΩ), bus speeds from 10 kHz to 1 MHz and ESD protection on USB and I²C complete the device. The firmware is updated via the built-in Wi-Fi access point in the browser or via USB, and the hardware is openly documented. For several sensors at once, the HALENG I²C Hub 10-Port Splitter for Grove, STEMMA QT and Qwiic is a good match.


Recommended Accessories:


Features:

  • Automatic bus diagnosis with a quality score from 0 to 100 % and concrete suggestions for improvement.
  • Connection via GROVE/STEMMA, QT/Qwiic and two 2.54 mm pin headers.
  • Switchable pull-ups in four steps, set separately for SDA and SCL with DIP switches.
  • Fault injection, stress test and sensor simulator for robustness tests and firmware development.
  • USB/I²C bridge with Python script for control and automation from a PC.
  • Firmware update via Wi-Fi access point or USB, openly documented hardware.

Application Examples:

  • Fast troubleshooting of a dead or unstable I²C bus without an oscilloscope
  • Identifying unknown sensor addresses by scan and database
  • First bus check when bringing up a new circuit
  • Robustness testing of prototypes with simulated interference and long cables
  • Incoming and final inspection of assemblies and sensors

Documentation:



Technical Specifications:

  • Manufacturer: HALENG
  • Manufacturer SKU: I2C-DOCTOR-WHITE
  • Microcontroller: ESP32 dual-core, 240 MHz, 4 MB flash
  • Display: 1.3 inch TFT, 240 × 240 pixels
  • I²C connectors: 1× GROVE/STEMMA, 1× QT/Qwiic, 2× 2.54 mm pin header (male/female)
  • I²C protection: 100 Ω series resistor per line (SDA/SCL)
  • I²C speeds: 10 / 50 / 100 / 200 / 400 kHz and 1 MHz
  • Switchable pull-ups: 10 kΩ / 4.7 kΩ / 2.2 kΩ / 1 kΩ
  • Input voltage: 5 V via USB-C
  • VDD (I²C): 3 to 5 V (5 V tolerant)
  • Current consumption: < 200 mA
  • VDD output current: max. approx. 100 mA (PTC fuse)
  • ESD protection (USB and I²C): ±8 kV air, ±4 kV contact
  • Serial interface: 115200 baud via USB-C
  • Firmware update: Wi-Fi access point (browser) or USB (ESP Flasher Tool)
  • Operating temperature: 0 to 70 °C
  • Dimensions: 84 × 50 × 15.5 mm (with housing)
  • Weight: 43 g (with housing)
  • Package dimensions: 145 × 100 × 25 mm
  • Gross weight: 55 g

Contents:

  • 1× HALENG I²C Doctor I2C Bus Tester and Analyser White (with housing)
  • 4× Jumper cable 15 cm male/female
  • 1× Quick start guide as QR code
  • 1× Feedback QR code

Write a review

Note: HTML is not translated!
    Bad           Good

HALENG I²C Doctor I2C Bus Tester and Analyser White

  • Brand: HALENG
  • Product Code: 426005
  • Availability: Out Of Stock
  • CHF49,90

  • Ex Tax: CHF46,16

Related Products

USB Logic Analyzer 8 Channel 24MHz

USB Logic Analyzer 8 Channel 24MHz

This logic analyzer records up to 8 digital signals at up to 24 MHz and is suitable for debugging an..

CHF17,90 Ex Tax: CHF16,56

8-Channel I2C Multiplexer TCA9548A

8-Channel I2C Multiplexer TCA9548A

This I2C multiplexer with the Texas Instruments TCA9548A allows several I2C sensors with the same ad..

CHF5,90 Ex Tax: CHF5,46

Gravity I2C HUB

Gravity I2C HUB

The Gravity I2C HUB from DFRobot distributes one I2C bus to up to eight devices. The input is a 4-pi..

CHF3,90 Ex Tax: CHF3,61

Industrial USB to UART/I2C/SPI/JTAG Converter

Industrial USB to UART/I2C/SPI/JTAG Converter

This USB to UART/I2C/SPI/JTAG converter from Waveshare is your ideal companion for connecting a vari..

CHF27,90 Ex Tax: CHF25,81

SLogic Combo 8 Logic Analyzer Development Tool

SLogic Combo 8 Logic Analyzer Development Tool

The SLogic Combo 8 from Sipeed, listed by DFRobot as FIT0956, combines four tools in one small devic..

CHF22,90 Ex Tax: CHF21,18

M5Stack Pa.HUB V2.1 I2C Expansion Unit 1 to 6 PCA9548A

M5Stack Pa.HUB V2.1 I2C Expansion Unit 1 to 6 PCA9548A

With the M5Stack Pa.HUB V2.1 expansion unit, you expand your I2C communication efficiently and flexi..

CHF8,90 Ex Tax: CHF8,23

Gravity I2C Address Changer

Gravity I2C Address Changer

The DFRobot address shifter uses the LTC4316 to translate the I2C address of a connected sensor in h..

CHF9,90 Ex Tax: CHF9,16

HALENG I²C Hub 10-Port Splitter for Grove, STEMMA QT and Qwiic

HALENG I²C Hub 10-Port Splitter for Grove, STEMMA QT and Qwiic

The I²C Hub from HALENG splits one I²C bus into ten connections: 4× GROVE/STEMMA, 4× QT/Qwiic and on..

CHF11,90 Ex Tax: CHF11,01

Tags: I²C Doctor, HALENG, Bus Tester, Analyser, Diagnosis, Pull-up, Address Scanner, Troubleshooting, ESP32, Grove, Qwiic, STEMMA QT, USB Bridge, Fault Injection, Measuring Device