Gravity I2C Address Changer

The DFRobot address shifter uses the LTC4316 to translate the I2C address of a connected sensor in hardware. This way two or more identical sensors with a fixed address run on the same bus without changes to the library or firmware; only the new address is entered in the code. The module sits between controller and sensor and works with 2.25 to 5.5 V.

To split identical sensors over separate channels there is the 8-Channel I2C Multiplexer TCA9548A.


Features:

  • Address translation in hardware with the LTC4316, no software multiplexer
  • Bit A6 of the address is always inverted, A5 and A4 depending on the DIP switch, giving four addresses; example according to DFRobot: 0x69 becomes 0x29, 0x09, 0x39 or 0x19
  • Further addresses with an 0805 resistor on the R2 pad, it controls the lower four bits A3 to A0
  • Power the module off and on again after changing the switches
  • Output RDY is HIGH as soon as the translation is ready
  • No clock stretching: not for sensors that need it, such as the BNO055 (DFRobot)
  • Gravity connectors for controller and sensor, plus solder holes for the included pin header

Application Examples:

  • Two identical motion or distance sensors on the same bus
  • Sensor arrays for environmental monitoring and agriculture
  • Robots with several identical I2C sensors

Documentation:


Technical Data:

  • Manufacturer: DFRobot
  • Manufacturer SKU: DFR1193
  • Chip: LTC4316
  • Supply voltage: 2.25 V to 5.5 V DC
  • Current consumption: 2 mA at 3.3 V
  • Addresses: 4 via DIP switches A5 and A4, more via resistor R2
  • Controller pins: VCC, GND, SCL, SDA, RDY
  • Sensor pins: VCC, GND, SCL, SDA
  • Operating temperature: 0 °C to 70 °C
  • Mounting holes: Ø 3.0 mm
  • Dimensions: 42 × 32 × 7 mm
  • Weight: 16 g

Scope of Delivery:

  • 1× Gravity I2C Address Changer
  • 1× pin header 10-pin, 2.54 mm pitch
  • 1× Gravity cable 4-pin, PH2.0 on both ends

Write a review

Note: HTML is not translated!
    Bad           Good

Gravity I2C Address Changer

  • Brand: DFRobot
  • Product Code: 424935
  • Availability: In Stock
  • CHF9,90

  • Ex Tax: CHF9,16

Related Products

PCF8574 I2C Port Expander I/O Extension 8 Pin

PCF8574 I2C Port Expander I/O Extension 8 Pin

This PCF8574 port expander adds 8 inputs and outputs to a Raspberry Pi or Arduino via the I2C bus, k..

CHF5,90 Ex Tax: CHF5,46

8-Channel I2C Multiplexer TCA9548A

8-Channel I2C Multiplexer TCA9548A

This I2C multiplexer with the Texas Instruments TCA9548A allows several I2C sensors with the same ad..

CHF5,90 Ex Tax: CHF5,46

Gravity CH423 I2C 24 Digital IO Port Expander

Gravity CH423 I2C 24 Digital IO Port Expander

The Gravity module from DFRobot with the CH423 provides 24 digital ports via I2C: 8 GPIO as input or..

CHF7,90 Ex Tax: CHF7,31

Gravity I2C HUB

Gravity I2C HUB

The Gravity I2C HUB from DFRobot distributes one I2C bus to up to eight devices. The input is a 4-pi..

CHF3,90 Ex Tax: CHF3,61

Gravity 2-Channel 15Bit 0-10V ADC Module

Gravity 2-Channel 15Bit 0-10V ADC Module

The DFRobot Gravity module measures two voltages from 0 to 10 V with the ADS1115 from Texas Instrume..

CHF12,90 Ex Tax: CHF11,93

Tags: Gravity, I2C, Address, Shifter, DFR1193, Module, Arduino, ESP32, Communication, Bus, Conflict, Sensor, Display, Prototyping, Interface, Logic, DFRobot, LTC4316