1x18650 Lithium Battery Shield 5V 3A / 3V 1A

This battery shield holds one 18650 cell and uses it to supply a Raspberry Pi, Arduino, ESP8266 or ESP32 with 5 V and 3 V. The built-in charging electronics recharge the cells via USB, the protection electronics protect against overcharging and deep discharge. Batteries are not included.

Caution: Observe the + and − polarity when inserting the 18650 cells, otherwise the charging chip will be destroyed. The holders are designed for 18650 cells without protection electronics, about 65 mm long. Longer cells with protection electronics do not fit.


Recommended Accessories:


Features:

  • Protection against overcharging and deep discharge
  • Charging via micro USB or USB-C with up to 0.5 A
  • 5 V 3 A via USB type A or 5 solder pads 5 V
  • 3 V 1 A via 5 solder pads 3 V
  • 4 red LEDs show the state of charge
  • After inserting the cells, briefly power the shield via USB, only then does it switch on
  • A short press on the side button K1 shows the state of charge and switches on
  • Switching off the 5 V and 3 V outputs: press button K1 twice
  • Switch SW1 enables or disables the automatic shutdown without a load

Application Examples:

  • Mobile power supply for Raspberry Pi, Arduino, ESP8266 and ESP32
  • Power bank for USB devices in custom projects

Technical Data:

  • Number of 18650 cells: 1
  • Protection electronics: overcharge and deep discharge protection
  • Charging: micro USB and USB-C
  • Maximum output current 5 V: 3 A (tested briefly up to 4 A)
  • Maximum output current 3 V: 1 A
  • Outputs: 1× USB type A socket 5 V, 5× solder pads 5 V, 5× solder pads 3 V
  • Mounting holes: 4× diameter 3 mm
  • Dimensions: 102 × 30 × 22 mm
  • Weight: 21 g

Scope of Delivery:

  • 1× 1x18650 Lithium Battery Shield 5V 3A / 3V 1A
  • Batteries are not included

Write a review

Note: HTML is not translated!
    Bad           Good

1x18650 Lithium Battery Shield 5V 3A / 3V 1A

  • Brand: purecrea
  • Product Code: 421083
  • Availability: Out Of Stock
  • CHF9.90

  • Ex Tax: CHF9.16

Related Products

Pin header male 1 X 40 pole RM 2.54mm straight short pin

Pin header male 1 X 40 pole RM 2.54mm straight short pin

This straight pin header with short pins is suitable for soldering onto boards and for breadboards. ..

CHF0.80 Ex Tax: CHF0.74

2x18650 Lithium Battery Shield 5V 3A / 3V 1A

2x18650 Lithium Battery Shield 5V 3A / 3V 1A

This battery shield holds two 18650 cells and uses it to supply a Raspberry Pi, Arduino, ESP8266 or ..

CHF8.90 Ex Tax: CHF8.23

4x18650 Lithium Battery Shield 5V 3A / 3V 1A

4x18650 Lithium Battery Shield 5V 3A / 3V 1A

This battery shield holds four 18650 cells and uses it to supply a Raspberry Pi, Arduino, ESP8266 or..

CHF16.90 Ex Tax: CHF15.63

UPS HAT for Raspberry Pi Uninterruptible Power Supply

UPS HAT for Raspberry Pi Uninterruptible Power Supply

With this Waveshare UPS HAT, a Raspberry Pi keeps running from two 18650 cells during a power interr..

CHF23.90 Ex Tax: CHF22.11

2x18650 Lithium Battery Shield Dfrobot 5V 2A / 3.3V

2x18650 Lithium Battery Shield Dfrobot 5V 2A / 3.3V

The battery holder from DFRobot takes two 18650 cells and turns them into a 5 V and 3.3 V supply. Ch..

CHF12.90 Ex Tax: CHF11.93

LilyGo TTGO T-BAT 18650 Battery Holder with CN3065 Solar Power Manager

LilyGo TTGO T-BAT 18650 Battery Holder with CN3065 Solar Power Manager

The LilyGo T-BAT combines a solar charge controller with the CN3065 chip and a battery holder for on..

CHF12.90 Ex Tax: CHF11.93

Tags: Batterieshield, 1x18650, Raspberry, ESP32, ESP8266, Arduino, LiPo, Li-Ion, NCR18650B, Panasonic, Cell, Battery, Battery operation, Battery operation, 18650, Battery compartment, Lithium, Lithium Block, Li-Ion Battery, Lithium Ion Battery, Built-in battery, Special battery, Industrial battery, V8, V9, Charge controller