5-30V Trigger Time Relay Module with USB
With this time relay module, a delay from 0.1 seconds to 999 minutes can be set, after which the relay switches on or off. It is triggered via a trigger input with 3 to 24 V. The module is powered via the input terminals or via micro USB. An LED display and four buttons are used to set the mode and times, reverse polarity protection is built in.
Features:
- Delay from 0.1 s to 999 min
- Trigger input 3 to 24 V
- Supply via terminals or micro USB, with reverse polarity protection
- LED display and buttons STOP, SET, UP and DOWN
- Mode P1: The relay picks up on the trigger signal and stays on for the time “OP”. On a new trigger during this time, the time continues (P1.1), restarts (P1.2) or the relay switches off (P1.3)
- Mode P2: After the trigger signal the time “CL” elapses, then the relay switches on for the time “OP” and off again
- Mode P3.1: After the trigger signal the relay switches on for “OP” and off for “CL”, this cycle repeats as often as set under “LOP”. A new trigger during “CL” restarts the sequence
- Mode P3.2: like P3.1, but without a trigger signal
- Mode P4: As long as the trigger signal is present, the relay stays on. When the signal drops, the time “OP” elapses, then the relay switches off
Connection and Operation:
- Supply: 6 to 30 V DC at the input terminals or 5 V via micro USB
- Trigger with 5 V logic: a 5 V output lies within the trigger range of 3 to 24 V
- Trigger with 3.3 V logic: a 3.3 V output is only just above the lower limit of 3 V, a level shifter gives more margin
- Load: observe the switching capacity printed on the relay
- Setting: press SET for 2 seconds, select the mode with UP and DOWN, confirm with SET and set the times. STOP moves the decimal point. Then press SET for 2 seconds, release and wait until the display shows 000
- During operation, STOP switches the module on or off
Application Examples:
- Staircase lighting and run-on control
- Switch-on delay for pumps, fans or other loads
- Cyclic switching in model making and on model railways
Documentation:
Technical Data:
- Input voltage: 6 to 30 V DC or 5 V via micro USB
- Trigger voltage: 3 to 24 V
- Time range: 0.1 s to 999 min
- Type: time relay with trigger input, electromechanical relay
- Mounting holes: Ø 3.1 mm, hole spacing 57 × 32 mm
- Dimensions: 63 × 38 × 17 mm
- Weight: 24 g
Scope of Delivery:
- 1× 5-30V Trigger Time Relay Module with USB
5-30V Trigger Time Relay Module with USB
- Brand: purecrea
- Product Code: 422454
- Availability: In Stock
-
CHF9,90
- Ex Tax: CHF9,16
Related Products
1-Channel Relay Module
The 1-channel relay module switches loads up to 30 V via a digital output of a microcontroller such ..
CHF5,50 Ex Tax: CHF5,09
Gravity Digital 5A Relay Module
The Gravity relay module from DFRobot switches a load via the contact of a relay, controlled by a di..
CHF6,90 Ex Tax: CHF6,38
5-30V Dual MOSFET Trigger Time Relay Module
This timer relay module allows a delay of 0.1 seconds to 999 minutes to be set, after which the outp..
CHF9,90 Ex Tax: CHF9,16
Tags: Time relay, Timer, Trigger, Relay, Time delay, Cycle, Timing, Relay, Delay, Startup delay, model railway, Power off delay, Model construction, delay relay, timer relay







