5-30V Dual MOSFET Trigger Time Relay Module

This timer relay module allows a delay of 0.1 seconds to 999 minutes to be set, after which the output switches on or off. Switching is done via MOSFETs instead of a mechanical relay. It is triggered via a trigger input with 3 to 24 V and supplied with 5 to 30 V. An LED display and four buttons are used to set the mode and times, reverse polarity protection is built in.

Recommended alternative with relay and USB supply: 5-30V Trigger Time Relay Module with USB


Features:

  • Delay from 0.1 s to 999 min
  • Trigger input 3 to 24 V
  • Output via MOSFETs, for DC loads
  • Supply 5 to 30 V DC, with reverse polarity protection
  • LED display and buttons STOP, SET, UP and DOWN
  • Mode P1: The output switches on at the trigger signal and stays on for the time “OP”. On a new trigger during this time, the time continues (P1.1), restarts (P1.2) or the output switches off (P1.3)
  • Mode P2: After the trigger signal the time “CL” elapses, then the output switches on for the time “OP” and off again
  • Mode P3.1: After the trigger signal the output switches on for “OP” and off for “CL”, this cycle repeats as often as set under “LOP”. A new trigger during “CL” restarts the sequence
  • Mode P3.2: like P3.1, but without a trigger signal
  • Mode P4: As long as the trigger signal is present, the output stays on. When the signal drops, the time “OP” elapses, then the output switches off

Connection and Operation:

  • Supply: 5 to 30 V DC at the input terminals
  • Trigger with 5 V logic: a 5 V output lies within the trigger range of 3 to 24 V
  • Trigger with 3.3 V logic: a 3.3 V output is only just above the lower limit of 3 V, a level shifter gives more margin
  • Load: DC only, observe the permissible current of the MOSFETs as printed
  • Setting: press SET for 2 seconds, select the mode with UP and DOWN, confirm with SET and set the times. STOP moves the decimal point. Then press SET for 2 seconds, release and wait until the display shows 000
  • During operation, STOP switches the module on or off

Application Examples:

  • Staircase lighting and run-on control with DC voltage
  • Switch-on delay for pumps, fans or other DC consumers
  • Cyclic circuits in model making and on model railways

Technical Data:

  • Input voltage: 5 V to 30 V DC
  • Trigger voltage: 3 V to 24 V
  • Time range: 0.1 s to 999 min
  • Type: timer relay with dual MOSFET
  • Mounting holes: diameter 3.1 mm, hole spacing 28.5 × 54 mm
  • Dimensions: 60 × 34.5 × 12 mm
  • Weight: 17 g

Scope of Delivery:

  • 1× 5-30V Dual MOSFET Trigger Time Relay Module

Write a review

Note: HTML is not translated!
    Bad           Good

5-30V Dual MOSFET Trigger Time Relay Module

  • Brand: purecrea
  • Product Code: 422453
  • Availability: In Stock
  • CHF9,90

  • Ex Tax: CHF9,16

Related Products

10A 600W MOSFET Driver 4-60V DC

10A 600W MOSFET Driver 4-60V DC

This MOSFET driver module switches larger DC loads up to 60 V from an Arduino or Raspberry Pi, such ..

CHF8,90 Ex Tax: CHF8,23

5-30V Trigger Time Relay Module with USB

5-30V Trigger Time Relay Module with USB

With this time relay module, a delay from 0.1 seconds to 999 minutes can be set, after which the rel..

CHF9,90 Ex Tax: CHF9,16

Tags: Time relay, Mosfet, FET, Timer, Trigger, Relay, MOSFET, Dual, Time delay, Cycle, Timing, Delay, Power-on delay, Model railway, Switch-off delay, Model building., timer relay, delay relay