Gravity Electrochemical Ozone Sensor 0-10 ppm with I2C

The Gravity ozone sensor from DFRobot measures the ozone concentration (O3) of the ambient air with an electrochemical cell in the range 0 to 10 ppm, with a resolution of 10 ppb. The reading comes digitally via I2C, the module runs on 3.3 V and 5 V on Arduino, ESP32 or Raspberry Pi. According to DFRobot, the sensor lifetime is over 2 years in air.

Alternative with I2C and UART: Gravity O3 Ozone Sensor I2C and UART

Note: The connection cable can be converted to male pins with a Dupont cable M-M, so that it also fits an Arduino UNO.


Recommended Accessories:


Features:

  • Electrochemical cell for ozone, measuring range 0 to 10 ppm
  • Digital reading via I2C, Gravity 4-pin
  • After first power-on let it run in for 24 to 48 hours, after that warm-up time max. 3 minutes (DFRobot)
  • Do not encapsulate with resin, do not operate in oxygen-free environments and not permanently in corrosive gases or high concentrations of organic gases (DFRobot)
  • Avoid contact with solvents, silicone and other adhesives, coatings and oils (DFRobot)
  • Do not open the white membrane on the sensor, do not pull the sensor off the module, do not mount in strong air draught (DFRobot)
  • Library and example code for Arduino by DFRobot

Application Examples:

  • Indoor air monitoring
  • Checking disinfection cabinets and ozone devices
  • Portable measuring devices
  • Smart home

Documentation:


Technical Data:

  • Manufacturer: DFRobot
  • Manufacturer SKU: SEN0321
  • Gas: ozone (O3)
  • Measuring principle: electrochemical
  • Operating voltage: 3.3 to 5.5 V DC
  • Output: I2C
  • Measuring range: 0 to 10 ppm
  • Resolution: 0.01 ppm (10 ppb)
  • Warm-up time: max. 3 minutes
  • Response time: max. 90 s
  • Recovery time: max. 90 s
  • Operating temperature: -20 to 50 °C
  • Humidity: 15 to 95 % RH, non-condensing
  • Storage temperature: -20 to 50 °C
  • Lifetime: over 2 years in air
  • Pins: SDA, SCL, GND, VCC
  • Dimensions: 37 × 27 × 15 mm
  • Weight: 22 g

Scope of Delivery:

  • 1× Gravity Electrochemical Ozone Sensor 0-10 ppm with I2C
  • 1× Gravity I2C sensor cable 4-pin
  • 4× Nylon standoff M3 × 10 mm
  • 8× Screw M3 × 5 mm

Write a review

Note: HTML is not translated!
    Bad           Good

Gravity Electrochemical Ozone Sensor 0-10 ppm with I2C

  • Brand: DFRobot
  • Product Code: 422573
  • Availability: In Stock
  • CHF54.90

  • Ex Tax: CHF50.79

Related Products

Dupont Cables M-M 10cm 20 Pieces

Dupont Cables M-M 10cm 20 Pieces

Dupont cables are used to connect components quickly. They are also known as jumper cables, test cab..

CHF1.90 Ex Tax: CHF1.76

Gravity O3 Ozone Sensor I2C and UART

Gravity O3 Ozone Sensor I2C and UART

This Gravity gas sensor from DFRobot measures ozone (O3) with an electrochemical cell in the range 0..

CHF149.00 Ex Tax: CHF137.84

Tags: Dfrobot, Ozone, Gas, Sensor, 2.54, 3.3V, ppm, Gravity, Ozone, SEN0321, O3