AI Binocular 3D Offline Sensor for Face / Hand Vein / QR Code

The recognition sensor from DFRobot recognises faces, palm veins and QR codes by itself, without computing power from the connected board. Two cameras (colour and infrared) capture depth and thus distinguish a real face from a photo or video. Up to 1000 faces and 1000 palm veins are stored in the module. The result is output via UART, for example to an Arduino UNO; via USB the module also delivers a video image like a webcam (UVC).


Recommended Accessories:


Features:

  • Face recognition with 3D liveness detection against photos and videos
  • Recognition of palm veins and palm prints, reading of QR codes
  • Memory for 1000 faces and 1000 palm veins, recognition runs offline in the module
  • Infrared illumination 850 nm, also recognises in the dark and outdoors without direct sunlight
  • UART with 115200 baud, user management with commands such as AT+GETUSERS and AT+DELUSER (wiki)
  • USB with UVC video (MJPEG), connections for speaker and microphone prepared
  • UART cable with Dupont female connectors, use Dupont cables M-M for breadboards and Arduino UNO
  • According to the DFRobot FAQ, do not remove the foam on the cameras; the chip gets warm during operation, this is normal

Application Examples:

  • Door lock and access control
  • Time recording with face or palm vein recognition
  • Self-service terminal with QR code
  • Smart home with person recognition

Documentation:


Technical Data:

  • Manufacturer: DFRobot
  • Manufacturer SKU: SEN0677
  • Processor: Arm 900 MHz, NPU 0.5 TOPS, RISC-V 600 MHz
  • Memory: 64 MB DDR2, 32 MB flash
  • Cameras: 2× 1/5 inch CMOS, 2 MP
  • Lens: 83° diagonal, best focus at 60 cm
  • Illumination: infrared 850 nm, LED 650 nm
  • USB: UVC video, MJPEG
  • Interface: UART 115200 baud
  • Supply: 5 to 12 V
  • Operating current: 320 to 330 mA at 8 V
  • Standby: 120 to 130 mA (automatic detection)
  • Start-up time: 0.9 to 2.5 s, depending on the number of users
  • Recognition distance: face 30 to 120 cm, palm vein and QR code 15 cm
  • Recognition angle: ±20° pitch and yaw
  • Liveness detection: FAR and FRR max. 1 % each
  • Face recognition: pass rate 98.85 %, FAR 0.001 %
  • UART pinout: black GND, yellow RX, green TX, red VCC 5 to 12 V
  • Operating temperature: -20 to 60 °C
  • Humidity: 10 to 93 % RH, non-condensing
  • Dimensions: 57.8 × 20 × 10.12 mm

Scope of Delivery:

  • 1× AI Binocular 3D sensor for face, palm vein and QR code
  • 1× cable 1.25 mm 4-pin to Dupont female
  • 1× USB data cable

Write a review

Note: HTML is not translated!
    Bad           Good

AI Binocular 3D Offline Sensor for Face / Hand Vein / QR Code

  • Brand: DFRobot
  • Product Code: 425053
  • Availability: In Stock
  • CHF49.90

  • Ex Tax: CHF46.16

Related Products

Dupont Cables M-M 10cm 20 Pieces

Dupont Cables M-M 10cm 20 Pieces

Dupont cables are used to connect components quickly. They are also known as jumper cables, test cab..

CHF1.90 Ex Tax: CHF1.76

DFRobot HUSKYLENS Easy-to-use AI Vision Camera Sensor

DFRobot HUSKYLENS Easy-to-use AI Vision Camera Sensor

The DFRobot HUSKYLENS is an AI camera with its own display that recognises faces, objects, lines, co..

CHF49.90 Ex Tax: CHF46.16

Finger Vein Scanner Sensor Module (A) with UART

Finger Vein Scanner Sensor Module (A) with UART

The Finger Vein Scanner Sensor Module (A) offers a precise and secure way for identification and acc..

CHF23.90 Ex Tax: CHF22.11

Tags: Face recognition, hand vein, biometrics, 3D vision, access control, AI sensor, offline, QR code, liveness detection, security, DFRobot, UART, authentication, door lock, smart home, SEN0677